How Much Does Well Pump Replacement Cost in 2026?
By Michael JohnsonUpdated 10 sources comparedHow we estimate
Most homeowners pay $1,000 to $2,800 to replace a well pump, with an average of about $1,850 installed. That average is the midpoint of the national figures published by HomeAdvisor ($1,899) and HomeGuide ($1,800). The biggest price drivers are the pump type (submersible, jet or constant-pressure), how deep the pump sits in the well, and whether the pressure tank, drop pipe and wire are replaced at the same time.
- Typical cost
- $1,000–$2,800
- National average
- $1,850
- Full range
- $400–$6,000
The typical range covers replacing a standard submersible or deep-well jet pump in a residential well, including the pump, labor, pulling and resetting the old unit, and basic fittings; deep wells, new drop pipe and wire, a new pressure tank or a constant-pressure system push the total toward the national high. Prices are per installed pump.
Well pump replacement cost by pump type
The table compiles installed prices (pump plus labor) from five independent cost guides. The QuoteRuler range is where those sources overlap for a typical residential replacement.
| Pump type | Typical well depth | Installed cost in sources | QuoteRuler typical range |
|---|---|---|---|
| Shallow-well jet pump | Water within about 25 ft | $400–$1,500 (HomeGuide, AHS, Angi) | $450–$1,400 |
| Deep-well jet pump | About 25–100 ft | $500–$2,200 (HomeGuide, AHS, Angi) | $600–$1,800 |
| Submersible pump | Up to about 250 ft | $1,000–$2,500 (HomeGuide, AHS, Angi) | $1,000–$2,500 |
| Submersible pump, deep well | 250 ft and deeper | $2,000–$10,000+ for wells over 150 ft (Angi) | $2,000–$4,000 |
| Constant-pressure system | Any depth | $1,300–$5,000 (HomeGuide, AHS, Angi, HomeAdvisor) | $2,000–$5,000 |
| Solar well pump | Off-grid or remote wells | $1,500–$6,500 (HomeGuide, Angi) | Varies widely |
Sources disagree mostly because of scope. HomeAdvisor's per-type table ($275–$1,550 for a submersible) appears to reflect the pump unit more than the full job, while its own headline range ($975–$2,824) and Angi's type table ($1,000–$2,500+ for a submersible) match HomeGuide and American Home Shield. Angi's depth tier for wells over 150 feet tops out at $10,000 or more, which likely includes well rehabilitation or very deep commercial-grade setups, so we used it only to set the deep-well range, not the typical one.
Estimate your cost
Pick the pump going into your well, tick any parts being replaced at the same time, and choose whether this is a scheduled job or an emergency call.
Ranges come from the sources listed at the end of this guide. The labor portion is adjusted for your state with BEA price data. Your final price depends on site conditions and local codes.
Submersible vs. jet pumps
A jet pump sits above ground, in a basement, pump house or well pit, and pulls water up by suction. Shallow-well jet pumps work only when the water is within roughly 25 feet; deep-well jet pumps use a second pipe and an ejector to reach farther. Because nothing has to be pulled out of the well, replacing a jet pump is usually the cheapest job: about $450 to $1,800 installed.
A submersible pump sits deep inside the well casing and pushes water up. It is the most common type in drilled wells. Replacement means pulling the pump, the drop pipe and the wire out of the well, then lowering everything back down, which is why labor is higher and why depth matters so much.
Cost by well depth and horsepower
Angi groups total cost by depth: under 25 feet runs $400 to $3,000+, 25 to 150 feet runs $1,200 to $5,500+, and wells over 150 feet run $2,000 to $10,000+. Deeper wells need more pipe and wire, more pulling time, sometimes a pump hoist truck, and a bigger motor.
Horsepower follows depth and flow. HomeAdvisor notes a 3/4 HP submersible can serve wells up to about 250 feet, and Bob Vila's sizing examples (2023 data) show a 1 HP pump delivering about 3 gallons per minute from 250 feet, versus about 1.5 HP for 15 gallons per minute. Larger motors and premium brands cost more, so ask your installer to quote the exact model and horsepower.
Constant-pressure (variable-speed) pumps
A constant-pressure system uses a variable-speed drive that changes motor speed to hold steady water pressure, instead of switching on and off between two pressure settings. Installed prices run about $2,000 to $5,000 (HomeGuide, AHS, HomeAdvisor), with Angi's range starting lower at $1,300. You pay more up front for steadier showers and fewer hard starts on the motor. Ask whether the quote includes the drive, a compatible sensor and any changes to the pressure tank.
Pump only vs. pump plus pressure tank
The pump itself is often the smaller part of the bill. This Old House says most pumps cost $200 to $500 before installation, and HomeGuide gives a wider $150 to $1,700 pump-only range that covers larger and constant-pressure models.
Replacing the pressure tank on the same visit adds about $500 to $1,000 installed (HomeGuide, HomeAdvisor's repair guide). HomeAdvisor's replacement guide lists a wider $800 to $3,800 for larger tanks. A waterlogged tank or ruptured bladder makes the pump short-cycle, turning on and off rapidly, which shortens the life of a new pump. If your tank is the same age as the failed pump, replacing both together avoids a second service call.
Labor vs. materials
Labor for a well pump replacement typically runs $250 to $1,000 (HomeAdvisor, Angi), and HomeGuide notes it can exceed $1,000 for difficult installs. Contractors bill about $45 to $150 per hour, and electricians $50 to $130 per hour for wiring work. Bob Vila's 2023 guide estimates a typical replacement takes about six hours.
We use a labor share of 40% in our state adjustments. The midpoint of the labor range ($625) is about a third of the $1,850 average, and deep wells, hoist trucks and electrical work push that share higher. The rest is the pump, pipe, wire, fittings and controls.
What drives the price up or down
- Depth. The single biggest variable for submersible pumps. More depth means more pipe and wire, more pulling time and a bigger pump.
- Drop pipe and wire. Old pipe and splices often get replaced while the pump is out. Angi says pipe replacement starts around $200, and Bob Vila's 2023 data puts submersible pipework in deep wells at $250 to $2,500 extra. Wiring by an electrician runs $162 to $525 (Bob Vila, 2023).
- Controls. A new control box costs $200 to $500 installed and a pressure switch $120 to $180 (HomeAdvisor, Modernize).
- Emergency timing. Weekend and after-hours labor runs about $100 to $200 per hour, roughly double the standard rate (HomeAdvisor, Modernize). With labor at about 40% of the bill, that adds roughly 40% to the total, which is what our calculator applies.
- Permits. Some areas require a permit, typically $50 to $200 (HomeAdvisor).
- Access. Wells in tight pits, under decks or far from a driveable path take longer to work on.
Signs the pump is failing, or something cheaper is
A home with no water does not always need a new pump. Before you approve a replacement, ask the contractor what they tested.
- No water at all: check the breaker first. A failed pressure switch ($120–$180), start capacitor ($100–$150) or control box ($200–$500) can stop a healthy pump (HomeAdvisor, Modernize).
- Pump clicks on and off rapidly: classic short-cycling, usually a waterlogged pressure tank or failed bladder rather than the pump.
- Pump runs nonstop or pressure is weak: possible causes include a worn pump, a leak in the drop pipe or a falling water level in the well.
- Sputtering faucets, air or sediment: often a sign the water level has dropped near the pump intake.
- Rising electric bills: a pump running longer to keep up can be wearing out.
A diagnostic visit typically costs a minimum service call of $100 to $150 (Modernize, HomeAdvisor), and a full well inspection runs $250 to $550 (HomeGuide). HomeGuide puts typical pump life at 10 to 15 years, so a pump near that age is a stronger candidate for replacement than for repair.
Well pump replacement cost by state
Labor rates vary widely between rural areas and high-cost metros, and well contractors are scarcer in some regions. The table below starts from our national range, compiled from the sources above, and adjusts only the labor portion (40%) using the Bureau of Economic Analysis Regional Price Parities for each state.
| State | Typical range | Average | vs. U.S. |
|---|---|---|---|
| Alabama | $960–$2,700 | $1,800 | -4.0% |
| Alaska | $1,000–$2,800 | $1,850 | +0.7% |
| Arizona | $1,000–$2,800 | $1,850 | +0.4% |
| Arkansas | $950–$2,650 | $1,750 | -5.4% |
| California | $1,050–$2,950 | $1,950 | +5.0% |
| Colorado | $1,000–$2,800 | $1,850 | +0.6% |
| Connecticut | $1,000–$2,850 | $1,900 | +1.5% |
| Delaware | $1,000–$2,800 | $1,850 | -0.3% |
| District of Columbia | $1,050–$2,900 | $1,950 | +4.3% |
| Florida | $1,000–$2,850 | $1,900 | +1.4% |
| Georgia | $990–$2,750 | $1,850 | -1.3% |
| Hawaii | $1,050–$2,900 | $1,900 | +3.4% |
| Idaho | $970–$2,700 | $1,800 | -3.4% |
| Illinois | $1,000–$2,800 | $1,850 | -0.4% |
| Indiana | $970–$2,700 | $1,800 | -3.1% |
| Iowa | $960–$2,650 | $1,750 | -4.5% |
| Kansas | $960–$2,700 | $1,800 | -4.0% |
| Kentucky | $960–$2,700 | $1,800 | -3.8% |
| Louisiana | $950–$2,650 | $1,750 | -4.7% |
| Maine | $990–$2,750 | $1,850 | -1.2% |
| Maryland | $1,000–$2,850 | $1,900 | +1.6% |
| Massachusetts | $1,050–$2,900 | $1,900 | +3.3% |
| Michigan | $980–$2,750 | $1,800 | -2.3% |
| Minnesota | $990–$2,800 | $1,850 | -0.6% |
| Mississippi | $950–$2,650 | $1,750 | -5.1% |
| Missouri | $970–$2,700 | $1,800 | -3.3% |
| Montana | $960–$2,700 | $1,800 | -3.9% |
| Nebraska | $960–$2,700 | $1,800 | -3.8% |
| Nevada | $990–$2,750 | $1,850 | -1.2% |
| New Hampshire | $1,000–$2,850 | $1,900 | +2.1% |
| New Jersey | $1,050–$2,900 | $1,900 | +3.6% |
| New Mexico | $960–$2,700 | $1,800 | -3.8% |
| New York | $1,050–$2,900 | $1,900 | +3.0% |
| North Carolina | $980–$2,750 | $1,800 | -2.4% |
| North Dakota | $950–$2,650 | $1,750 | -4.6% |
| Ohio | $970–$2,700 | $1,800 | -3.3% |
| Oklahoma | $950–$2,650 | $1,750 | -4.7% |
| Oregon | $1,000–$2,850 | $1,900 | +1.9% |
| Pennsylvania | $990–$2,750 | $1,850 | -1.0% |
| Rhode Island | $1,000–$2,800 | $1,850 | +0.6% |
| South Carolina | $970–$2,700 | $1,800 | -2.7% |
| South Dakota | $950–$2,650 | $1,750 | -4.8% |
| Tennessee | $970–$2,700 | $1,800 | -3.0% |
| Texas | $990–$2,750 | $1,850 | -1.1% |
| Utah | $980–$2,750 | $1,800 | -2.0% |
| Vermont | $990–$2,750 | $1,800 | -1.4% |
| Virginia | $1,000–$2,800 | $1,850 | +0.3% |
| Washington | $1,050–$2,900 | $1,900 | +3.4% |
| West Virginia | $960–$2,700 | $1,750 | -4.1% |
| Wisconsin | $970–$2,700 | $1,800 | -2.8% |
| Wyoming | $960–$2,700 | $1,800 | -3.7% |
Treat these as a starting point. Local well depths matter as much as local wages, so a state with deep aquifers can cost more than its price level suggests.
DIY or hire a pro?
Jet pumps on shallow wells are the one case where an experienced homeowner can sometimes do the swap, since the pump is above ground. Submersible pumps should be handled by a licensed well or pump installer. Pulling a few hundred feet of water-filled pipe is heavy and dangerous, a dropped pump can be lost in the well, and the job involves 230-volt wiring. Some states require a licensed pump installer for any work inside the well, and a botched job can contaminate the water supply.
Test your water after the work
Opening the well can let bacteria in. The EPA recommends testing a private well immediately whenever you repair or replace part of the well system, and annually for coliform bacteria, nitrates, total dissolved solids and pH. A basic lab test costs about $130 to $200, and county health departments often sell kits for $20 to $75 (HomeGuide). Use a state-certified lab. If the results show hardness or iron problems, our water softener installation cost guide covers treatment options.
How to save money on a well pump replacement
- Diagnose before you replace. A $120 pressure switch or $150 capacitor fix is far cheaper than a $1,850 pump.
- Replace aging parts together. If the pressure tank or control box is as old as the pump, one visit costs less than two.
- Avoid emergency rates when you can. If you still have some water, schedule a weekday visit instead of paying after-hours labor.
- Get at least three quotes from licensed well contractors, and ask each to price the same pump horsepower, depth and brand.
- Check your home warranty. Some plans cover well pumps; American Home Shield's add-on, for example, caps coverage at $1,500.
- Ask about the pump warranty. A slightly pricier pump with a longer warranty can cost less over its life.
How to compare well pump quotes
A fair quote should list:
- Pump brand, model, horsepower, voltage and the depth it will be set at.
- Whether drop pipe, wire, torque arrestor, check valves and splice kits are being replaced, with lengths.
- Pressure tank, pressure switch and control box: replaced or reused.
- Removal and disposal of the old pump.
- Permit fees, if required in your area.
- Well disinfection and water testing, if offered.
- Labor warranty and manufacturer warranty, separately.
Red flags: a replacement quoted without testing the switch, capacitor or tank; no stated pump depth or horsepower; pressure to buy a constant-pressure system without explaining why; or a much lower bid that reuses corroded pipe and wire without saying so.
Hidden costs people forget
- Pressure tank that fails soon after the new pump goes in: $500–$1,000.
- Pipe and wire found corroded once the pump is out: $200 and up, and up to $2,500 in deep wells.
- Pitless adapter repair at the well casing: $150–$450 (HomeAdvisor).
- Water testing after the job: $130–$200 for a basic lab panel.
- Electrical upgrades if the new pump needs a different circuit or breaker.
- Bottled water or a hotel while you wait for an emergency repair.
If your home also relies on a septic system, it's worth tracking its age alongside the well; our septic tank replacement cost guide covers what that job costs.
Bottom line
A standard submersible or deep-well jet pump replacement usually costs $1,000 to $2,800 installed, and $1,850 is a realistic national midpoint. Deep wells, new drop pipe and wire, a pressure tank or a constant-pressure system can push the total to $4,000 to $6,000. Before you approve a new pump, have the pressure switch, control box and tank tested, since those fixes cost a fraction of a pump. Get three itemized quotes, and test your water once the work is done.
Frequently asked questions
How much does it cost to replace a well pump and pressure tank together?
Expect roughly $1,500 to $3,800 for a standard submersible pump plus a new pressure tank, combining the typical pump replacement range ($1,000–$2,800) with a pressure tank at $500–$1,000 installed (HomeGuide, HomeAdvisor). Large tanks can cost more; HomeAdvisor's replacement guide lists pressure tanks at $800–$3,800. Doing both on one visit usually saves a second service call.
How long does a well pump usually last?
HomeGuide puts the typical life of a well pump at 10 to 15 years with proper care, while the well itself can last 40 years or more. A pump that short-cycles because of a failed pressure tank or switch can wear out much sooner, so fixing those parts protects the new pump.
Can a homeowner replace a well pump?
An above-ground jet pump on a shallow well is within reach for an experienced DIYer where local rules allow it. Submersible pumps are different: the pump, hundreds of feet of water-filled pipe and the wire must be pulled and lowered back down, often with a pump hoist, and the job involves 230-volt wiring. Most homeowners hire a licensed well or pump contractor, and some states require one.
How much does a submersible well pump replacement cost?
A submersible pump replacement typically costs $1,000 to $2,500 installed (HomeGuide, American Home Shield, Angi). Deeper wells cost more because there is more pipe and wire to pull and reset; Angi's depth table runs from $1,200–$5,500 for 25–150 ft wells up to $2,000–$10,000 or more for wells over 150 ft.
How much does it cost to replace a well pressure switch?
A pressure switch replacement runs about $120 to $180 including labor, according to HomeAdvisor (Modernize lists $120–$175). The part itself costs only $20–$40. Because a failed switch can look exactly like a dead pump, it's worth having it tested before you agree to a full replacement.
Is a well pump covered by homeowners insurance?
Usually only if the pump is damaged by a covered event such as a lightning strike or fire; normal wear and motor burnout are typically excluded, so read your policy's terms. Home warranty plans sometimes cover well pumps, but with limits: American Home Shield's well pump add-on, for example, caps coverage at $1,500.
Should I test my well water after the pump is replaced?
Yes. The EPA recommends testing a private well right away whenever you repair or replace part of the well system, because opening the well can introduce bacteria. A basic lab test covering coliform bacteria, nitrates and common minerals costs about $130–$200, and many county health departments sell kits for $20–$75 (HomeGuide).
Sources
We compared these sources to build the QuoteRuler range. State figures adjust the labor portion (40% of the total) using the BEA Regional Price Parities.
- How Much Does a Well Pump Cost to Replace? — HomeGuide. Used for: Replacement $400–$2,500; national average $1,800 (min $200, max $20,000); average range $1,000–$2,500; submersible $1,000–$2,500; deep jet (50–100 ft) $500–$1,400; shallow jet (up to 25 ft) $400–$1,000; constant pressure $2,000–$5,000; solar $1,500–$6,500; pump only $150–$1,700; plumbing labor $250–$800, over $1,000 for difficult installs; electrician $50–$130/hr; pressure tank $500–$1,000; pressure switch part $25–$100; tank bladder $50–$100; pump motor $500–$1,000; lifespan 10–15 years, well 40+ years. Page shows no update date..
- How Much Does It Cost to Replace a Well Pump? — HomeAdvisor (Angi Inc.). Used for: Title references 2025 data. National average $1,899; normal range $975–$2,824; full range $200–$5,800; submersible $275–$1,550; shallow jet $230–$1,000; deep jet $440–$1,200; constant pressure $2,000–$5,000; solar $1,800–$6,500; labor $250–$1,000 at $45–$150/hr; permits $50–$200; pressure tank $800–$3,800; FAQ notes a 3/4 HP submersible serves wells up to about 250 ft..
- How Much Does a Well Pump Replacement Cost? — Angi. Used for: Same parent company and dataset as HomeAdvisor, so not counted as an independent source. Average $1,897; most spend $974–$2,821; pump alone $400–$6,500; submersible $1,000–$2,500+; shallow jet $450–$1,500; deep jet $800–$2,200+; constant pressure $1,300–$4,000+; by well depth: under 25 ft $400–$3,000+, 25–150 ft $1,200–$5,500+, over 150 ft $2,000–$10,000+; labor $250–$1,000; electrician $50–$100/hr; pipe replacement starts around $200..
- How Much Does Well Pump Repair Cost? — HomeAdvisor (Angi Inc.). Used for: Title references 2025 data. Repair average $972, range $373–$1,620; pressure switch $20–$40 part, $120–$180 installed; control box $50–$200 part, $200–$500 installed; start capacitor $100–$150 installed; pressure tank $500–$1,000; pitless adapter $150–$450; house call $100–$150 (up to $300); weekend/emergency labor about $100/hr, roughly double the ~$50/hr standard rate; complete well inspection $300–$600..
- Well Pump Repair Cost — Modernize. Used for: Updated August 12, 2026. Repair $375–$1,600 (avg. about $950–$1,000); replacement $1,000–$2,800; pressure switch $120–$175; control box $200–$500; capacitor $100–$150; parts-only submersible $250–$1,000+, deep jet $400–$800, shallow jet $200–$500; labor $50–$100/hr; minimum service call $100–$150; emergency or after-hours labor $100–$200/hr..
- What Is the Cost to Replace a Well Pump? — American Home Shield. Used for: Dated February 6, 2026. Submersible $1,000–$2,500; shallow-well jet $400–$1,400; deep-well jet $500–$1,400; constant pressure $2,000–$5,000; survey figure of $70–$1,700 (80th percentile, 2024 survey, includes smaller repairs); AHS well pump add-on coverage limit $1,500..
- Well Pump Cost and Installation Guide (2026) — This Old House. Used for: Updated March 5, 2026. Replacement and installation $900–$2,500; pump alone typically $200–$500 (Home Depot units: shallow jet ~$200, deep jet ~$300, submersible ~$500)..
- How Much Does a Well Pump Cost to Install? — Bob Vila. Used for: Older data (last updated April 28, 2023), used only for line items not priced by newer sources: submersible pipework in deep wells adds $250–$2,500; electrician for wiring $162–$525; typical job about 6 hours; sizing examples (3 GPM at 250 ft needs about 1 HP, 15 GPM at 250 ft about 1.5 HP)..
- How Much Does a Well Inspection Cost? — HomeGuide. Used for: Well inspection $250–$550; basic water test (bacteria, metals, nitrate/nitrite and more) $130–$200; advanced test $220–$450; county health department kits $20–$75; DIY kits $25–$50 single contaminant. Page shows no update date..
- Protect Your Home's Water — U.S. Environmental Protection Agency. Used for: Test private wells annually for total coliform bacteria, nitrates, total dissolved solids and pH; test immediately after repairing or replacing part of the well system; use state-certified drinking water labs..
- Regional Price Parities by State, 2023 — U.S. Bureau of Economic Analysis. Used for: state cost adjustments.